NINE MILE METALS ANNOUNCES PHASE 1 BULK SAMPLE UPDATE AT NINE MILE BROOK HIGH GRADE LENS OF 13.71% CUEQ OVER 15.10M
TORONTO, ON, Monday, March 2nd , 2026 – NINE MILE METALS LTD. (CSE: NINE, OTC-PINK: VMSXF, FSE: KQ9)-(the “Company” or “Nine Mile”) is pleased to announce that it is conducting Bulk Sample Metallurgical Analysis on the Nine Mile Brook VMS High Grade Lens with SGS Canada and Glencore Canada. Glencore and SGS will be conducting their own collaborated scope of work, including sample preparation, assaying, mineralogical studies, and metallurgical testing. SGS will provide (2) specific samples to Glencore, who will be conducting their own metallurgical – mineralogical analysis for their Horne Smelter in Rouyn-Noranda, Quebec. HIGHLIGHTS: (2) Nine Mile Brook Lens representative samples will be collected, one from the high-grade Cu portion, a second from the Pb-Zn-Ag end of the Lens, weighing up to 1 Tonne each. The samples will be placed in large totes, shrink wrapped and shipped to SGS in Lakefield, Ontario for crushing, grinding, Assay, Mineralogical and Metallurgical Analysis. In addition, DDH NM220004 Drill Core representing the entire 15.10m intersection of High-Grade Cu will be shipped to SGS Canada for 1st phase grinding & preparation and forwarded to Glencore for their proprietary IsaMILLTM Technology and metallurgical analysis. SGS will crush the Cu Rich Sample according to Glencore’s parameters. Glencore’s IsaMILLTM technology is the world’s only horizontal high speed stirred media mill designed for energy efficient ultrafine grinding in mining of base metals in a reliable compact scalable footprint. Nine Mile Metals will also deliver Drill Core representative of the entire Cu intersection to SGS to Crush to the same specifications requested by Glencore and deliver the sample accordingly. Glencore will have both a large sample and an entire drill intersect sample for IsaMILLTM process & Metallurgical Analysis. SGS will do a mineralogical scan, Bond Test to determine hardness, and conduct head grade analysis for Cu, Pb, Zn, Fe, S, Au, Ag, and Indium. Metallurgical testing will follow including gravity tests to assess copper recovery. SGS will also conduct (6) floatation tests to assess metallurgical response. Previous investigative work by RPC Science and Engineering (RPC) on potential Cu-Pb-Zn recovery of the lens material identified anomalous Indium in the deposit, a critical mineral used in semiconductors, electronics, and aerospace industries. SGS is the World’s Leading Testing, Inspecting and Certification company, operating in 115 countries operating over 2500 Laboratories. A Swiss company of excellence helping organizations achieve the highest level of quality, compliance, and sustainability. The required Notice of Planned Work has been submitted for the Project. TABLE 1: Assay Summary, DDH-NM220004, Nine Mile Brook 2022 DDH-NM220004 Certified Assays Cu% Zn% Pb% Ag (g/t) Ag (oz) Au (g/t) Cu Eq % From To Width TOTAL 0.00m 15.10m 15.10m 10.12 1.00 1.41 91.47 2.94 0.84 13.71 TABLE 2: Certified Assays, Nine Mile Brook Drill Program 2022 – Previously Released (7-8-2022) DDH HOLE – NM220004 (CERTIFIED LAB RESULTS) (15.10 Continuous Meters – Sampled) Sample # From To Width Cu % Zn % Pb % Ag g/t Ag (oz) Au g/t Cu Eq % 683529 0.00 1.20 1.20 m 0.94 2.22 0.83 12.00 0.39 0.24 2.18 683530 1.20 1.50 0.30 m 7.40 17.70 8.56 188.00 6.05 2.06 19.88 683531 1.50 2.50 1.00 m 12.80 1.19 3.60 177.00 5.69 0.896 18.76 683532 2.50 3.50 1.00 m 18.55 0.26 0.36 64.00 2.06 0.552 20.81 683533 3.50 4.50 1.00 m 11.80 0.30 0.59 78.00 2.51 1.64 15.81 683534 4.50 5.50 1.00 m 16.85 0.57 0.98 125.00 4.02 1.13 21.4 683535 5.50 6.50 1.00 m 12.65 1.19 7.89 212.00 6.82 0.842 19.94 683536 6.50 7.56 1.06 m 16.10 0.70 0.60 153.00 4.92 1.765 22.06 683537 7.56 8.56 1.00 m 4.33 0.16 0.07 10.00 0.32 0.152 4.8 683538 8.56 9.56 1.00 m 3.68 0.08 0.06 6.00 0.19 0.158 4.05 683539 9.56 10.00 0.44 m 0.47 0.13 0.02 2.00 0.06 0.376 1.03 683540 10.00 10.68 0.68 m 3.93 0.07 0.07 19.00 0.61 0.523 5.1 683541 Standard 683542 10.68 11.68 1.00 m 15.45 2.03 2.45 173.00 5.56 1.055 21.55 683543 11.68 12.68 1.00 m 12.40 0.26 0.37 91.00 2.93 0.902 15.72 683544 12.68 13.68 1.00 m 11.90 0.07 0.48 126.00 4.05 1.39 16.61 683545 13.68 14.10 0.42 m 14.80 0.09 0.42 139.00 4.47 1.465 19.90 683546 14.10 15.10 1.00 m 2.83 0.08 0.06 14.00 0.45 0.118 3.33 TOTAL 0.00 15.10 15.10 m 10.12 1.00 1.41 91.47 2.94 0.84 13.71 Including Zone 1 VMS 1.20 7.56 m 6.36 m 14.46 1.50 2.61 137.51 4.42 1.19 19.83 Zone 2 Seds 7.56 m 10.68 m 3.12 m 3.49 0.11 0.06 9.55 0.30 0.27 4.09 Zone 3 VMS 10.68 m 4.10 m 3.42 m 13.44 0.70 1.02 131.11 4.22 1.16 13.44 Gary Lohman, P.Geo., VP Exploration & Director stated “This is a critical phase for our Bulk Sample Program at Nine Mile Brook. This is an extremely High-Grade Lens (13.71% CuEq over 15.10m) and we will test the direct to Smelter Option through Glencore’s Analysis & Metallurgical testing. This is a key milestone for us and look forward to announcing the results and our path forward to completion.” Patrick J. Cruickshank, MBA, CEO & Director, stated “ We are extremely excited to enter Phase #1 of our Nine Mile Brook High Grade VMS Lens up to 22.06% CuEq intersections. This is the culmination of over 1 year of discussion, analysis, and design creating a path forward for our High-Grade Lens Bulk Sample Project. We would like to thank our Technical Team, SGS Canada, in Lakefield Ontario, and the Glencore Technology Group in Australia & New York. Endless months of defining this stage and now we are moving forward to execute on it. We look forward to reporting on Phase #1 results and initiating Phase #2.“ Figure 2: DDH – NM2200004 Core Samples #683531 (18.76% CuEq) and #683532 (20.81% CuEq) Analysis and QAQC All samples were submitted to and analyzed at ALS Global, an independent commercial laboratory for both the sample preparation and assaying. ALS is a commercial laboratory independent of Nine Mile Metals Ltd. Samples submitted through ALS are run through standard preparation methods and analysed using
NINE MILE METALS ANNOUNCES CERTIFIED ASSAYS FROM DDH-WD-25-02 OF 2.78% CUEQ OVER 32.10 METERS, INCLUDING 4.78% CUEQ OVER 11.52 METERS AND 5.64% CUEQ OVER 6.02 METERS
TORONTO, ON, Tuesday, February 17th, 2026 – NINE MILE METALS LTD. (CSE: NINE, OTC-PINK: VMSXF, FSE: KQ9)-(the “Company” or “Nine Mile”) is pleased to announce it has received certified assays for drill hole WD-25-02 at the Wedge Mine situated in the renowned Bathurst Mining Camp, New Brunswick (BMC). WD-25-02 HIGHLIGHTS: DDH WD-25-02 was collared on the same drill pad as WD-25-01 and drilled at an azimuth of 310 degrees and a dip of -50 degrees to a depth of 203 meters to expand on the mineralization intersected in drill hole WD-25-01. Collared in the hanging wall sediments, the drill hole intersected 32.10 meters of Cu bearing mineralization within a sediment / volcanic package that includes 3 distinct VMS (Cu, Pb, Zn, Ag, Au) horizons between 138.72 and 170.82 m., (Table 1). In addition to copper bearing sulphides, the 3 Horizons are further characterized by elevated Ag and Au, with assays up to 70 g/t Ag and 1.19 g/t Au respectively. Horizon 1 mineralization consists of Cu bearing pyritic VMS and has a true width of 2.5 meters (138.72 – 141.22 m.) occurring at a brecciated contact between sheared graphitic argillite and massive VMS, assaying 3.09% Cu, 1.02% Pb, 4.88% Zn, 61.57 g/t Ag, and 1.01 g/t Au. Horizon 2 is defined by a sequence of weakly mineralized (Py, Cpy) and massive copper bearing sulphides (VMS- Cu, Pb, Zn, Ag, Au) between 150.30 and 165.32 m., a true width of 15.02 meters, assaying 2.14% Cu, 0.52% Pb, 1.00 % Zn, 11 g/t Ag, and 0.40 g/t Au. Included in Horizon 2 is 6.02 meter (true width) of massive VMS mineralization between 159.30 – 165.32 m. assaying 4.63% Cu, 0.27% Pb, 0.79% Zn, 12.50 g/t Ag, and 0.42 g/t Au. Within this interval, sample 338291 was the highest Cu assay in the drill hole, returning 6.52% over 1 meter between 161.30 – 162.30 meters (Figure 5), further confirming the presence of exceptional grade potential at the Wedge. Horizon 3 is a 2.82-meter intercept (true width) of massive VMS (Cu, Pb, Zn, Ag, Au) assaying 2.91% Cu, 0.96% Pb, 7.13% Zn, 36.65 g/t Ag, and 0.72 g/t Au. TABLE 1: Assay Summary (Weighted Averages) From (m) To (m) Width (m) Cu % Pb (%) Zn (%) Ag (g/t) Au (g/t) Cu Eq Overall Mineralization 138.72 170.82 32.10 1.53 0.47 1.81 14.09 0.35 2.78 Horizon 1 138.72 141.22 2.50 3.09 1.02 4.88 61.57 1.01 6.95 Horizon 2 150.30 165.32 15.02 2.14 0.52 1.00 11.00 0.40 3.19 Includes 159.30 170.82 11.52 3.20 0.48 2.48 17.00 0.43 4.78 159.30 165.32 6.02 4.63 0.27 0.79 12.50 0.42 5.64 Horizon 3 168.00 170.82 2.82 2.91 0.96 7.13 36.65 0.72 6.49 Mike Dufresne, Technical Team & President of Apex Geoscience stated “ Well it is quite thrilling to see the increase in Cu grades to the West in the VMS and mostly coincident with increase gold and roughly approximating the Conductive Plate Modelling. The Copper and Gold is well associated.” Horizon 1: Horizon 1 mineralization occurs at a graphitic argillite, massive pyritic VMS contact. The mineralization is fine grained with some visible chalcopyrite and minor galena (Pb) and sphalerite (Zn). The sheared graphitic contact is a marker horizon with the same style of VMS mineralization also occurring in drill holes WD-25-01, WD-25-2B, WD-W5-04 and WD-25-05. TABLE 2: Horizon 1 Certified Assays, (138.72 – 141.22 meters) Sample From To Width Ag Au Cu Pb Zn Cu Eq # (m.) (m.) (m.) g/t g/t % % % % 338267 138.72 139.18 0.46 22 0.52 0.769 0.414 2.10 2.45 338268 139.18 140.18 1.00 71 1.06 4.22 1.150 3.58 8.01 338269 140.18 141.22 1.04 70 1.19 3.02 1.175 7.36 7.94 “We are quite pleased by the results from WD-25-02. Not only do the assays confirm the presence of copper at depth, but the multi-element nature of the VMS mineralization is best reflected in the copper equivalent calculations where the presence of Ag, Au and Zn significantly changes the rock value. We will report on the assays from drill hole WD-25-01 as soon as the lab completes analysis of elements that were over limit. With the assays arriving and compilation – modeling underway, permitting of additional drill holes in the west will allow us to expand on the success of this program. Down hole geophysics (BHEM) is planned for the 2 holes collared in the northwest and select drill holes in the south to target additional mineralization along strike and at depth as these deposits typically have multiple, mineralized lenses that can pinch and swell. ” commented Gary Lohman, P.Geo., VP Exploration & Director. Horizon 2: The first appearance of copper mineralization in Zone 2 occurs at 150.30 – 154.40 meters with local chalcopyrite noted within a sedimentary sequence. A contact zone followed by a small void between 155.00 – 158.00 meters where VMS mineralization is present on both the upper and lower sides, the latter consisting of 95% sulphides. Visible semi massive to massive chalcopyrite is seen throughout the sequence (Figure 5 below). TABLE 3: Horizon 2 Certified Assays, (150.30 – 165.32 meters) Sample From To Width Ag Au Cu Pb Zn Cu Eq # (m.) (m.) (m.) g/t g/t % % % % 338280 150.30 150.90 0.60 7 0.227 0.250 0.318 0.607 0.88 338281 150.90 151.90 1.00 11 0.423 0.292 0.776 1.22 1.46 338282 151.90 152.90 1.00 16 0.532 0.440 0.633 1.15 1.80 338283 152.90 153.90 1.00 3 0.058 0.047 0.175 0.504 0.05 338284 153.90 154.40 0.50 4 0.064 0.020 0.538 0.436 0.37 338285 154.40 155.00 0.60 27 0.600 0.523 2.730 3.83 3.18 338286 155.00 158.00 3.00 10 0.558 0.823 0.674 0.98 2.11 338287 158.00 158.30 0.30 7 0.416 0.911 0.152 0.343 1.68 338288 158.30 159.30 1.00 5 0.107 0.200 0.366 1.37 0.84 338289 159.30 160.30 1.00 16 0.340 4.50 0.642 0.50 5.46 338290 160.30 161.30 1.00 9 0.363 5.92 0.074 0.294 6.63 338291 161.30 162.30 1.00 16 0.453 6.52 0.254 1.025 7.69 338292 162.30 163.30 1.00 16 0.394 4.42 0.456 0.579 5.44 338293 163.30
NINE MILE METALS INTERSECTS 44 METERS OF COPPER MINERALIZATION AND PROVIDES DRILL PROGRAM UPDATE
TORONTO, ONTARIO, CANADA – Tuesday, February 10TH, 2026, NINE MILE METALS LTD. (CSE: NINE, OTCPINK: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”), is pleased to provide the details of drill hole WD-25-05 in addition to a summary of the 2025 drill program completed in December at the Wedge Project. Drillhole WD-25-05: DDH WD-25-05 collared on the same drill pad as WD-25-01 and drilled at an azimuth of 310 degrees and a dip of -60 to a final depth of 275 meters. DDH-WD-25-05 was successful, intersecting massive VMS (Cu, Pb, Zn, Ag, Au) mineralization between 155.52 – 157.80 meters (Figure 1) followed by 40 meters of mineralized felsic volcanics (rhyolite) as seen in Figure 2 between 157.80 and 197.80 meters before terminating in sediments. Mineralization consisted of both pyrite and chalcopyrite as disseminations, masses, and associated with quartz bands parallel to bedding. All drill core has been measured, logged, photographed, marked, and cut for sampling at the company’s warehouse in Bathurst, New Brunswick. A quick XRF analysis was also completed for sulphide confirmation – filtering and width identification in definition for sampling core for Actlabs Analysis. A total of 55 sections were delivered to ALS Global in Moncton, New Brunswick for Base and Precious Metals analysis, including Antimony. Drill Holes BHEM -01 and BHEM-02: Both drill holes were collared on permitted drill pads in the northwest along the western extension (Figure 4). The drill core for both BHEM-01 and BHEM-02 were solid with minimal faulting / fracturing in the host sediments providing ideal drill holes for surveying and subsequent follow up. Collared outside of known mineralization, the holes are well positioned to locate and model adjacent mineralization with no interference from a conductive source within the drill hole. Both holes are capped and easily accessible, the drill pads available for extending drilling further west and if required, additional depth. Gary Lohman, VP Exploration, Director stated, “ Our Wedge Drill Program has been very successful, intersecting Massive Cu bearing VMS where targeted in the western extension of the Wedge Deposit, as designed. Two holes were also drilled in the Northwest area to facilitate an upcoming BHEM survey, their locations in solid rock on the flanks of previous underground workings. In addition to identifying additional mineralization, the size and scale of the individual geological units and results from the upcoming BHEM program will assist in modeling the deposit and targeting additional drilling along the western extension. After our successful drilling in the southern lower extension of the deposit, our knowledge of the deposit and mineralization has increased and identified new areas of priority that were not permitted for this past drill program. We have identified new drill collar locations to continue to test the Copper Zone on the western extension in addition to potential locations that avoid the shear zone in the south. New permitting is underway in preparation of an exciting 2026 campaign at the Wedge, including our West Wedge and Tribag Target Trend drill programs”. 2025 Drill Program Overview: The program consisted of 7 drill holes totaling 1,654 meters with 5 holes targeting copper mineralization in the western extension of the Wedge Mine with two additional holes collared in the northwest to facilitate BHEM (Bore Hole Electromagnetic) surveying this spring. The goal is to map the depth of the deposit and define the new copper zone. We should also be able to map the western parameters of the deposit, heading west towards the Tribag and West Wedge along trend. The 2025 drill program was highly successful, with all five drill holes targeting copper mineralization intersecting both massive VMS (Cu, Pb, Zn, Ag, Au) and banded copper sulphide mineralization. The two holes collared to facilitate BHEM geophysical surveying were also successful, collared in the northwest portion of the western extension, away from the large, graphitic shear zone that bounds the deposit in the south and west of the interpreted extent of previous, underground workings. BHEM surveying has its best results when drilled away from the mineralization and the magnetic interference. The five drill holes targeting mineralization were all collared in the southwest, crossing through a brecciated, graphitic shear zone (tectonic melange) before intersecting a well-defined massive VMS (Cu, Pb, Zn, Ag, Au) horizon. This is characteristic of the mineralized contact after which a sequence of intercalated sediments and volcanics are cut prior to the holes intersecting the main zone of VMS mineralization with mineralized widths between 13 and 48 meters. The VMS mineralization consisted of abundant pyrite and lesser chalcopyrite, sphalerite, and galena. Local, secondary copper, covellite (CuS) and bornite (Cu5FeS4), was also identified in drill holes WD-25-02 and WD-25-04. In the west, the metal zonation appears different than the drill holes completed in the east with the prevalence of a greater concentration of chalcopyrite and pyrite with lesser galena (Pb) and sphalerite (Zn). Although it is early in the process, we have confirmed the presence abundant chalcopyrite and coarser grained pyrite in the western extension. The key observations in this program include: Graphitic Shear Zone in contact with VMS confirmed as a diagnostic marker horizon in the southwest. Mineralized siliceous volcanics were intersected in numerous drill holes, defining an additional, mineralized sequence. VMS mineralization occurs in multiple horizons as seen in holes WD-25-01 and WD-25-02. The intersected units (Argillite, VMS and Felsic Volcanics) are of substantial width and extent which will assist in the 3D modeling of the deposit and subsequent drill hole targeting. Patrick J Cruickshank, MBA, CEO & Director stated “we are thrilled with the success of our Wedge Phase 2 Drill Program. To have all 5 holes strike mineralization was more than we expected. It is a testament to our Technical Team and specifically, Mike Dufresne and Gary Lohman. We already have identified Phase 3 Drill holes and are determined more than ever to expand this deposit’s footprint and expose this entire new 3rd High Grade Copper Lens. In addition, the BHEM surveys, the Phase 3 Wedge Drilling, the TriBag & West Wedge drilling
NINE MILE METALS ANNOUNCES COMPLETION OF DDH WD-25-04, CONFIRMING 40M OF MINERALIZATION AT DEPTH
TORONTO, ONTARIO, CANADA – THURSDAY, JANUARY 22nd, 2026, NINE MILE METALS LTD. (CSE: NINE, OTCQB: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”), is pleased to announce that the 4th drill hole in its Wedge Western Extension Drill Program (DDH-WD-25-04) has been completed. DDH WD-25-04 was collared on the same drill pad as WD-25-01 and drilled at an azimuth of 335 degrees and a dip of -60 degrees to a final depth of 239 meters to expand the mineralization in WD-25-01 at depth. DDH WD-25-04 was successful, with 40m of mineralization, first intersected at 158 meters and continuing to approximately 198 meters. Once again, secondary Copper, both Covellite and Bornite was present in the hole. At 158 meters, copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au) was found in contact with sheared, graphitic sediments. Between 162.0 and 183 meters, the drill hole intersected a sequence of sheared silicified volcanics (rhyolite) with parallel bands of 5 – 8% sulphides including pyrite and chalcopyrite. At 183 meters, the volume of sulphides increases to 50- 60% with visible pyrite and chalcopyrite, the contrast in mineralization styles shown in Figure 1, the chalcopyrite occurring as both mineralized bands and as disseminations Figure 3. The sulphide mineralization in the drill hole occurs within silicified volcanics, the base of section brecciated before transitioning to sediments. FIGURE 1: Cu bearing VMS mineralization FIGURE 2: Chalcopyrite (CuFeS2) and Covellite (CuS) mineralization. FIGURE 3: Chalcopyrite occuring both mineralized bands and dissminations (left), VMS mineralization (right). Patrick J Cruickshank, CEO & Director stated “Our drill program successes continue with this 40m intersect of mineralization in this 4th drill hole WD-25-04. This is the 4th Hole of a planned 7, designed by our Technical Team headed by Mike Dufresne and Gary Lohman. The programs successes to date displays the hard work from all the 3D modelling of historical data, new geophysical work by our team and most important, our compilation, interpretation and hours of consultations with experts such as Jim Walker, PhD, from the ever-supportive NB DEM Team in Bathurst. Our Team is already laying the groundwork for the 2nd Phase of the Wedge program and the Tribag, West Wedge Program for this spring, testing this string of anomalies stretching over 6 kms west of our Wedge Deposit. The closing of our oversubscribed Financing ensures an extensive 2026-2027 Exploration Program at all four projects in our portfolio including our return to Nine Mile Brook . Our financial strength should allow us to have a lengthy program this year with the luxury of not having to raise for the foreseeable future reduced dilution risk for our shareholders. We look forward to continuing to update our shareholders with the completion of this program and the release of our Certified Assays.” FIGURE 4: Grey, Silicified Rhyolite, an important host of mineralization in the VMS System in the BMC FIGURE 5: Drill Hole Location, WD-25-04 Gary Lohman, Director, P.Geo., VP Exploration, stated ”The mineralization is massive in character, fine grained, with basic Fe (Pyrite) and Cu sulphides (Chalcopyrite – Covellite), mineralogy as we have seen in recent drilling. Visible covellite (CuS) was locally present, adding a high grade component to the system. Again, these values explain what we are seeing in our drill core from our first 3 holes. (WD-25-01 & WD-25-02 & WD-25-02B). We are extremely encouraged and look forward to the WD-25-01 Certified Drill Core Assay Results.” Patrick J. Cruickshank, MBA, CEO & Director, stated “Our current Wedge Program continues to demonstrate the high-grade quality of the sampling of this deposit. These results are simply outstanding. Our current Drill Program was designed with this quality of mineralization below and I believe our 1st (3) announced drill holes clearly demonstrates this success. This is definitely a special copper rich deposit. We look forward to sharing our summary of our next drill hole in our program.” Qualified Person The technical content of this news release pertaining to the Wedge Project was reviewed and approved by Gary Lohman, P.Geo., a non-independent qualified person as defined by National Instrument 43-101. Copper Equivalent (Cu-Eq) for these surface grab samples is calculated based on December 16, 2025, pricing: US$ 5.35/lb Cu, US$ 0.88/lb Pb, US$ 1.37/lb Zn, US$ 67.10/oz Ag, and US$ 4337.70/oz Au, with 80% metallurgical recoveries assumed for all metals. Since it is unclear which metals will be the principal products, assuming different recoveries is premature at this stage. Therefore, an 80% recovery rate is justified. About Nine Mile Metals Ltd.: Nine Mile Metals Ltd. is a Canadian public mineral exploration company focused on VMS (Cu, Pb, Zn, Ag and Au) exploration in the world-famous Bathurst Mining Camp, New Brunswick, Canada. The Company’s primary business objective is to explore its four VMS Projects: Nine Mile Brook VMS Project; California Lake VMS Project; and the Canoe Landing Lake (East – West) Project and the Wedge VMS Project. The Company is focused on exploration of Minerals for Technology (MFT), positioning for the boom in EV and green technologies requiring Copper, Silver, Lead and Zinc with a hedge with Gold. Social Media [post-footer-social-links] ON BEHALF OF NINE MILE METALS LTD. “Patrick J. Cruickshank, MBA” CEO and Director T: +1.506-800-0581 E: info@ninemilemetals.com Forward-Looking Information: This press release may include forward-looking information within the meaning of Canadian securities legislation, concerning the business of Nine Mile. Forward-looking information is based on certain key expectations and assumptions made by the management of Nine Mile. In some cases, you can identify forward-looking statements by the use of words such as “will,” “may,” “would,” “expect,” “intend,” “plan,” “seek,” “anticipate,” “believe,” “estimate,” “predict,” “potential,” “continue,” “likely,” “could” and variations of these terms and similar expressions, or the negative of these terms or similar expressions. Forward-looking statements in this press release include that (a) our Geophysics Program will turn its focus next to the Nine Mile Brook Project and our Eastern Portfolio, (b) both Plates A and C are large, massive, strong conductors, having both the length and depth parameters for a potentially large, mineralized body consistent with
NINE MILE METALS ANNOUNCES CERTIFIED HIGH-GRADE ASSAY RESULTS UP TO 15.00% COPPER FROM THE WEDGE PROJECT, BATHURST, NEW BRUNSWICK
TORONTO, ON. Monday, December 29th, 2025 – NINE MILE METALS LTD. (CSE: NINE, OTC PINK: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”) is pleased to announce Certified Assay results for volcanogenic massive sulphide (VMS) mineralization collected from the pre-drill area on the Wedge VMS Project, in the world-famous Bathurst Mining Camp (BMC), New Brunswick, Canada. TABLE 1: ALS Global Certified Assay Results: Sample # Cu Pb Zn Au Ag Cu Eq % % % g/t g/t % 280447 10.90 0.02 0.04 0.17 6.00 11.22 280448 9.95 0.03 0.03 0.24 6.20 10.36 280449 9.11 0.04 0.49 0.31 6.90 9.73 280450 10.20 0.12 0.44 0.18 7.70 10.68 280451 10.60 0.05 0.24 0.19 7.60 11.02 280452 10.10 0.41 0.76 0.24 11.60 10.86 280453 0.48 0.01 0.01 0.12 1.20 0.65 280454 2.31 0.19 0.45 0.26 3.50 2.83 280455 0.10 0.01 0.01 0.09 0.80 0.23 280456 10.20 0.05 0.34 0.19 6.40 10.64 280457 10.10 0.04 0.39 0.17 5.70 10.51 280458 3.09 0.39 1.42 0.32 5.50 4.00 280459 2.40 1.76 2.17 0.29 22.70 4.00 280460 15.00 0.05 0.11 0.71 42.00 16.64 280461 13.30 0.07 0.09 0.58 25.70 14.49 280462 14.20 0.04 0.12 0.21 48.10 15.37 280463 13.30 0.07 0.10 0.52 29.50 14.49 280464 13.70 0.06 0.11 0.25 30.90 14.60 280465 0.33 0.01 0.02 0.12 1.70 0.51 280466 0.09 0.01 0.02 0.12 1.20 0.26 The assays were shipped to ActLabs in Fredericton, New Brunswick for preparation with final analysis of pulps conducted in Ancaster, Ontario. The primary analytical method for the Wedge samples is UT-7, multi-element Peroxide “Total” Fusion (ICP-OES+MS). When overlimit results are returned, ore grade analysis is triggered and conducted utilizing Code 8-AR-ICP-OES. Gold analysis is treated separately by 30g Fire Assay and AA finish, method 1A2. Ag is also treated separately by method 1E Ag. QA /QC controls involve inserting standards in the samples stream at set intervals. Samples 280461 through 280464 below (Figure 1) are examples of the massive Hi-Grade Copper sulphide mineralization (Chalcopyrite). Covellite is also clearly seen in sample #280461 and #280463, as a dark blue cast in colour. The samples were collected in the area highlighted in Figure 2, immediately to the west of the footings for the old hoist and the remains of the shaft. These are well-known landmarks. FIGURE 1: HIGHLIGHTED SAMPLES Figure 2: 2025 Sample Area Gary Lohman, Director, P.Geo., VP Exploration, stated ”The mineralization is massive in character, fine grained, with basic Fe (Pyrite) and Cu sulphides (Chalcopyrite – Covellite), mineralogy as we have seen in recent drilling. Visible covellite (CuS) was locally present, adding a high grade component to the system. Again, these values explain what we are seeing in our drill core from our first 3 holes. (WD-25-01 & WD-25-02 & WD-25-02B). We are extremely encouraged and look forward to the WD-25-01 Certified Drill Core Assay Results.” Patrick J. Cruickshank, MBA, CEO & Director, stated “Our current Wedge Program continues to demonstrate the high-grade quality of the sampling of this deposit. These results are simply outstanding. Our current Drill Program was designed with this quality of mineralization below and I believe our 1st (3) announced drill holes clearly demonstrates this success. This is definitely a special copper rich deposit. We look forward to sharing our summary of our next drill hole in our program.” Qualified Person The technical content of this news release pertaining to the Wedge Project was reviewed and approved by Gary Lohman, P.Geo., a non-independent qualified person as defined by National Instrument 43-101. Copper Equivalent (Cu-Eq) for these surface grab samples is calculated based on December 16, 2025, pricing: US$ 5.35/lb Cu, US$ 0.88/lb Pb, US$ 1.37/lb Zn, US$ 67.10/oz Ag, and US$ 4337.70/oz Au, with 80% metallurgical recoveries assumed for all metals. Since it is unclear which metals will be the principal products, assuming different recoveries is premature at this stage. Therefore, an 80% recovery rate is justified. About Nine Mile Metals Ltd.: Nine Mile Metals Ltd. is a Canadian public mineral exploration company focused on VMS (Cu, Pb, Zn, Ag and Au) exploration in the world-famous Bathurst Mining Camp, New Brunswick, Canada. The Company’s primary business objective is to explore its four VMS Projects: Nine Mile Brook VMS Project; California Lake VMS Project; and the Canoe Landing Lake (East – West) Project and the Wedge VMS Project. The Company is focused on exploration of Minerals for Technology (MFT), positioning for the boom in EV and green technologies requiring Copper, Silver, Lead and Zinc with a hedge with Gold. ON BEHALF OF NINE MILE METALS LTD. “Patrick J. Cruickshank, MBA” CEO and Director T: 506-804-6117 E: patrick@ninemilemetals.com Forward-Looking Information: This press release may include forward-looking information within the meaning of Canadian securities legislation, concerning the business of Nine Mile. Forward-looking information is based on certain key expectations and assumptions made by the management of Nine Mile. In some cases, you can identify forward-looking statements by the use of words such as “will,” “may,” “would,” “expect,” “intend,” “plan,” “seek,” “anticipate,” “believe,” “estimate,” “predict,” “potential,” “continue,” “likely,” “could” and variations of these terms and similar expressions, or the negative of these terms or similar expressions. Forward-looking statements in this press release include that (a) our Geophysics Program will turn its focus next to the Nine Mile Brook Project and our Eastern Portfolio, (b) both Plates A and C are large, massive, strong conductors, having both the length and depth parameters for a potentially large, mineralized body consistent with example deposits throughout the BMC, and (c) we look forward to announcing our Phase 2 Advanced Geophysics results, including full interpretations and high priority targets for our Western Portfolio. Although Nine Mile believes that the expectations and assumptions on which such forward-looking information is based are reasonable, undue reliance should not be placed on the forward-looking information because Nine Mile can give no assurance that they will prove to be correct. The Canadian Securities Exchange (CSE) has not reviewed and does not accept responsibility for the adequacy or the accuracy of the contents of this release.
NINE MILE METALS ANNOUNCES COMPLETION OF DDH WD-25-02B AND CONTINUES TO CONFIRM (2) ZONES OF COPPER RICH VMS WITH 66 METERS OF MINERALIZATION AT THE WEDGE PROJECT
TORONTO, ONTARIO, CANADA. MONDAY, DECEMBER 22nd , 2025 – NINE MILE METALS LTD. (CSE: NINE, OTCQB: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”) is pleased to announce that the 3rd drill hole in its Wedge Western Extension Drill Program (DDH-WD-25-02B) has been completed. DDH WD-25-02B was collared approximately 60 meters northwest of WD-25-01 and drilled at an azimuth of 325 degrees and a dip of -50 degrees to a final depth of 122 meters further increasing the mineralized footprint of the target to the west (Figure 3). DDH WD-25-02B was successful, with massive copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au) found associated with the contact breccia at 56.4m depth with mineralization continuing to 122 meters. The sulphide mineralization in the drill hole occurred in both sediments and volcanics, terminating in massive copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au) with visible Chalcopyrite (CuFeS2) as seen in Figure 1. Downhole ground conditions in the fault zone (sand seams, gouge) led to the termination of the drill hole at 122 meters, as we were drilling through a massive copper zone (Figure 1). Most Sample sections between 53.0 and 122.0 meters were 3 meters in length, to provide the best overall data for the drill hole. Smaller sample widths were identified and cut where appropriate. With massive mineralization present at the base of the drill hole, a new drill hole is being designed by the Technical Team, to be initiated from the other side of the fault zone, (New – to be permitted) in Phase 2 – 2026. FIGURE 1: Visible VMS Quality Mineralization, Massive Chalcopyrite (CuFeS2 ) – Samples cut for Lab Processing FIGURE 2: Massive Copper Mineralization Throughout Cut Drill Core in DDH WD-25-02B Sample Section FIGURE 3: Drill Hole Locations, WD-25-01, WD-25-02B All drill core has been measured, logged, photographed, marked and cut for sampling at the company’s warehouse in Bathurst, New Brunswick. A quick XRF analysis was also completed for sulphide confirmation – filtering and width identification in definition for sampling core for ALS Global. A total of (27) 3 meter sections have been identified for Base and Precious Metals analysis, including Antimony, and have been shipped to ALSGlobal, Moncton, New Brunswick for processing. Gary Lohman, VP Exploration, Director stated, “Drilling continues to intersect massive copper bearing mineralization in the western portion of the Wedge. The style of the mineralization varies from massive VMS (Cu-Pb-Zn-Ag-Au) to sequences of intercalated volcanics and VMS bands. XRF analysis has confirmed the high presence of copper, and we look forward to obtaining the permits required to drill this high-grade zone from the other side of the fault zone in the spring drill phase. The mineralization just continues to impress. We look forward to testing the thickness of this area of the target zone.” Patrick J. Cruickshank, MBA, CEO & Director, stated, “Our 3rd drill hole, WD-25-02B continues to demonstrate the high-quality mineralization at this deposit and now we are testing the depth on the western flank of the targets. The samples clearly confirm multiple Copper rich zones, and we are systematically drilling the area to help identify the size and scale of this body. We look forward to revisiting this area of the Target Plate in our next phase of drilling, as we were just entering a very impressive high grade copper zone. We now have (3) completed drill holes with all core sample sections delivered ALS Global Labs for “Rush” processing. Our team has been highly motivated to process and ship the drill core quickly for expediated assay results from ALS Global (Moncton).” The disclosure of technical information in this news release has been prepared in accordance with Canadian regulatory requirements as set out in National Instrument 43-101 – Standards of Disclosure for Mineral Projects (“NI 43-101”) and reviewed and approved by Gary Lohman, B.Sc., PGO., VP Exploration and Director who acts as the Company’s Qualified Person, and is not independent of the Company. About Nine Mile Metals Ltd.: Nine Mile Metals Ltd. is a Canadian public mineral exploration company focused on VMS (Cu, Pb, Zn, Ag and Au) exploration in the world-famous Bathurst Mining Camp, New Brunswick, Canada. The Company’s primary business objective is to explore its four VMS Projects: Nine Mile Brook VMS Project; California Lake VMS Project; and the Canoe Landing Lake (East – West) Project and the Wedge VMS Project. The Company is focused on exploration of Minerals for Technology (MFT), positioning for the boom in EV and green technologies requiring Copper, Silver, Lead and Zinc with a hedge with Gold. Social Media [post-footer-social-links] ON BEHALF OF NINE MILE METALS LTD. “Patrick J. Cruickshank, MBA” CEO and Director T: +1.506-800-0581 E: info@ninemilemetals.com Forward-Looking Information: This press release may include forward-looking information within the meaning of Canadian securities legislation, concerning the business of Nine Mile. Forward-looking information is based on certain key expectations and assumptions made by the management of Nine Mile. In some cases, you can identify forward-looking statements by the use of words such as “will,” “may,” “would,” “expect,” “intend,” “plan,” “seek,” “anticipate,” “believe,” “estimate,” “predict,” “potential,” “continue,” “likely,” “could” and variations of these terms and similar expressions, or the negative of these terms or similar expressions. Forward-looking statements in this press release include that (a) our Geophysics Program will turn its focus next to the Nine Mile Brook Project and our Eastern Portfolio, (b) both Plates A and C are large, massive, strong conductors, having both the length and depth parameters for a potentially large, mineralized body consistent with example deposits throughout the BMC, and (c) we look forward to announcing our Phase 2 Advanced Geophysics results, including full interpretations and high priority targets for our Western Portfolio. Although Nine Mile believes that the expectations and assumptions on which such forward-looking information is based are reasonable, undue reliance should not be placed on the forward-looking information because Nine Mile can give no assurance that they will prove to be correct. The Canadian Securities Exchange (CSE) has not reviewed and does not accept responsibility for the adequacy or the
NINE MILE METALS ANNOUNCES CERTIFIED HIGH-GRADE ASSAY RESULTS UP TO 15.21% (CuEq) COPPER FROM THE WEDGE PROJECT, BATHURST, NEW BRUNSWICK
TORONTO, ON. Wednesday, December 17th , 2025 – NINE MILE METALS LTD. (CSE: NINE, OTCQB: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”) is pleased to announce Certified Assay results for volcanogenic massive sulphide (VMS) mineralization collected from the pre-drill area on the Wedge VMS Project, in the world-famous Bathurst Mining Camp, New Brunswick, Canada (“BMC”). Discovered in 1956, Cominco operated the Wedge mine between 1962 to 1968 producing 1.5 million tonnes of predominantly copper ore. At the time of closure, (crown pillar collapsed), only the upper portion of the deposit was mined. The expectation is that the lower 60% + remains untouched based upon recent drill testing and extends at depth with the 3D modeling. TABLE 1: ALS Global Certified Assay Results Sample # Cu Pb Zn Au Ag Cu Eq % % % g/t g/t % 280365 7.52 0.123 0.052 0.257 12 8.06 280366 13.65 0.088 0.082 0.826 32 15.21 280367 1.625 0.043 0.016 0.229 8 2.05 280368 1.51 0.037 0.014 0.309 6 1.99 280369 0.514 0.091 0.265 0.277 7 1.04 280370 9.25 0.067 1.04 0.126 8 9.82 280371 3.45 0.246 0.804 0.149 6 3.98 280372 1.385 0.064 1.245 0.144 4 1.95 280373 1.52 0.818 0.029 0.516 25 2.70 280374 2.01 0.425 0.03 0.503 25 3.10 280375 3.53 0.031 0.013 0.287 6 3.98 280376 10.1 0.028 0.046 0.097 5 10.32 280377 2.83 0.05 1.105 0.12 5 3.35 280378 4.92 0.766 0.057 0.262 30 5.88 280379 3.07 0.063 0.714 0.163 3 3.50 280380 1.235 1.705 3.98 0.213 18 3.09 280381 10.95 0.033 0.057 0.078 5 11.28 280382 4.87 0.082 0.148 0.122 4 5.13 The assays were shipped to ALS Global in Moncton New Brunswick for preparation with final analysis of pulps conducted in Vancouver, British Columbia. The primary analytical method for the Wedge samples, as recommended after consultation with ALS staff, involves multi-element ICP analysis, method ME-ICP61a . When overlimit results are returned, ore grade analysis is triggered and conducted utilizing methods ME-OG62 and Cu-OG62. Gold analysis is treated separately by 30g Fire Assay and AA finish. QA /QC controls involve inserting standards in the samples stream at set intervals. Samples 280370 and 280366 below (Figure 1) are examples of the massive Hi-Grade Copper sulphide mineralization The samples were collected in the small area highlighted in Figure 2, immediately to the west of the footings for the old hoist and the remains of the shaft. These are well-known landmarks. FIGURE 1: HIGHLIGHTED SAMPLES Figure 2: 2025 Sample Area Gary Lohman, Director, P.Geo., VP Exploration, stated ”The surface samples collected along the western portion of Wedge reflects the copper rich nature of the Wedge. These samples were massive in character, fine grained, with basic Fe and Cu sulphide mineralogy like sections seen in recent drilling, especially drill hole WD-25-02 as reported on November 26, 2025. Early observations of drill core are encouraging, and we look forward to the reporting the drill results as soon as available from ALS Global.” Patrick J. Cruickshank, MBA, CEO & Director, stated “The grade of these samples in our drill area is highly indicative of the quality of the asset and the potential of the economics of this mine. Our technology indicates that this asset is much bigger and potentially part of a regional clustering of the Massive Sulphides targets. Our Technical Team is working diligently to keep up with the drill team on our current program. Our Team is logging, measuring, photographing, sampling, cutting, and sending to the Labs for assay processing. We are focused on executing this as soon as possible to get the results into the pipeline and back as fast as we can. We are currently completing the summary of DDH #3 and will announce our findings expeditiously.” Qualified Person The technical content of this news release pertaining to the Wedge Project was reviewed and approved by Gary Lohman, P.Geo., a non-independent qualified person as defined by National Instrument 43-101. Copper Equivalent (Cu-Eq) for these surface grab samples is calculated based on December 16, 2025, pricing: US$ 5.35/lb Cu, US$ 0.88/lb Pb, US$ 1.38/lb Zn, US$ 63.97/oz Ag, and US$ 4333.15/oz Au, with 80% metallurgical recoveries assumed for all metals. Since it is unclear which metals will be the principal products, assuming different recoveries is premature at this stage. Therefore, an 80% recovery rate is justified. About Nine Mile Metals Ltd.: Nine Mile Metals Ltd. is a Canadian public mineral exploration company focused on VMS (Cu, Pb, Zn, Ag and Au) exploration in the world-famous Bathurst Mining Camp, New Brunswick, Canada. The Company’s primary business objective is to explore its four VMS Projects: Nine Mile Brook VMS Project; California Lake VMS Project; and the Canoe Landing Lake (East – West) Project and the Wedge VMS Project. The Company is focused on exploration of Minerals for Technology (MFT), positioning for the boom in EV and green technologies requiring Copper, Silver, Lead and Zinc with a hedge with Gold. ON BEHALF OF NINE MILE METALS LTD. “Patrick J. Cruickshank, MBA” CEO and Director T: 506-804-6117 E: patrick@ninemilemetals.com Forward-Looking Information: This press release may include forward-looking information within the meaning of Canadian securities legislation, concerning the business of Nine Mile. Forward-looking information is based on certain key expectations and assumptions made by the management of Nine Mile. In some cases, you can identify forward-looking statements by the use of words such as “will,” “may,” “would,” “expect,” “intend,” “plan,” “seek,” “anticipate,” “believe,” “estimate,” “predict,” “potential,” “continue,” “likely,” “could” and variations of these terms and similar expressions, or the negative of these terms or similar expressions. Forward-looking statements in this press release include that (a) our Geophysics Program will turn its focus next to the Nine Mile Brook Project and our Eastern Portfolio, (b) both Plates A and C are large, massive, strong conductors, having both the length and depth parameters for a potentially large, mineralized body consistent with example deposits throughout the BMC, and (c) we look forward to announcing our Phase 2 Advanced Geophysics results, including full interpretations and high priority targets for
NINE MILE METALS ANNOUNCES COMPLETION OF DDH WD-25-02 AND CONTINUES TO CONFIRM (2) ZONES OF COPPER RICH VMS MINERALIZATION AT THE WEDGE PROJECT DRILL PROGRAM
TORONTO, ONTARIO, CANADA – WEDNESDAY DECEMBER 3rd, 2025, NINE MILE METALS LTD. (CSE: NINE, OTCQB: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”), is pleased to announce that the 2nd drill hole in its Wedge Western Extension Drill Program (DDH-WD-25-02) has been completed and is in progress on its 3RD hole (DDH-WD-25-02B). DDH WD-25-02 was collared on the same drill pad as WD-25-01 and drilled at an azimuth of 310 degrees and a dip of -50 degrees to intersect the first plate approximately 50 meters west of Hole WD-25-01, increasing the mineralized zone along strike, to the west. (Figure 3). The hole completed at 203m at depth. DDH WD-25-02 was successful, intersecting massive copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au). Massive copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au) were found associated with the contact breccia at 139m depth with a second zone of massive copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au) intersected at 155 meters, having an approximate true width of 20 meters. The sulphide mineralogy in WD-25-02 is readily visible, especially the massive copper mineralization, as shown in Figures 1 & 2. Chalcopyrite (CuFeS2) occurs as masses, streaks and blebs while more local Pb-Zn mineralization is well banded with sphalerite (Zn) the dominant sulphide. Local bornite (Cu5FeS4) and Covellite (CuS) is visibly present, the bornite displays its characteristic “Purple Peacock Copper Bloom” and Covellite its “Blue Copper”, as seen in Figure 1. All drill core has been measured, logged, photographed, marked and cut for sampling at the company’s warehouse in Bathurst, New Brunswick. A quick XRF analysis was also completed for sulphide confirmation – filtering and width identification in definition for sampling core for Actlabs Analysis. A total of 55 sections have been identified for Base and Precious Metals analysis, including Antimony, for Actlabs, Fredericton, New Brunswick. FIGURE 1: Visible Massive Copper Mineralization from Zone 1 & 2 (including Covellite (CuS) & Bornite (Cu5FeS4 ). Gary Lohman, VP Exploration, Director stated, “We are pleased with our technical preparation of this drill program and quality of our Lens targeting. The western extension of this deposit is robust and copper rich. Very positive to confirm the thickness of this plate intersection as we stepped approximately 50m west of DDH-WD-25-01. Our data modelling suggests a 3rd potential Zone of mineralization which Mike Dufresne of Apex Geoscience is modeling and designing (2) potential Drill holes to test that prospective Zone from the western flank area, thus avoiding a sheer zone from the south. We look forward to moving to the Northwest area of this extension program”. Patrick J. Cruickshank, MBA, CEO & Director, stated, “Once again, we have intersected quality mineralization at the desired Target Plates at DDH-25-02, as designed and set out by our Technical Team. The visible mineralization and copper rich sulphides is just spectacular. The presence of Bornite and Covellite is a strong indicator of the quality of this deposit. This western flank area is being confirmed as a rich Copper Lens, one hole at a time. We are on track to increase the Wedge Mine’s mineralized footprint to the west and at depth. The next drill hole in our campaign is DDH-WD-25-02B, which is underway and we look forward to sharing our next summary update shortly.” About Nine Mile Metals Ltd.: Nine Mile Metals Ltd. is a Canadian public mineral exploration company focused on VMS (Cu, Pb, Zn, Ag and Au) exploration in the world-famous Bathurst Mining Camp, New Brunswick, Canada. The Company’s primary business objective is to explore its four VMS Projects: Nine Mile Brook VMS Project; California Lake VMS Project; and the Canoe Landing Lake (East – West) Project and the Wedge VMS Project. The Company is focused on exploration of Minerals for Technology (MFT), positioning for the boom in EV and green technologies requiring Copper, Silver, Lead and Zinc with a hedge with Gold. Social Media [post-footer-social-links] ON BEHALF OF NINE MILE METALS LTD. “Patrick J. Cruickshank, MBA” CEO and Director T: +1.506-800-0581 E: info@ninemilemetals.com Forward-Looking Information: This press release may include forward-looking information within the meaning of Canadian securities legislation, concerning the business of Nine Mile. Forward-looking information is based on certain key expectations and assumptions made by the management of Nine Mile. In some cases, you can identify forward-looking statements by the use of words such as “will,” “may,” “would,” “expect,” “intend,” “plan,” “seek,” “anticipate,” “believe,” “estimate,” “predict,” “potential,” “continue,” “likely,” “could” and variations of these terms and similar expressions, or the negative of these terms or similar expressions. Forward-looking statements in this press release include that (a) our Geophysics Program will turn its focus next to the Nine Mile Brook Project and our Eastern Portfolio, (b) both Plates A and C are large, massive, strong conductors, having both the length and depth parameters for a potentially large, mineralized body consistent with example deposits throughout the BMC, and (c) we look forward to announcing our Phase 2 Advanced Geophysics results, including full interpretations and high priority targets for our Western Portfolio. Although Nine Mile believes that the expectations and assumptions on which such forward-looking information is based are reasonable, undue reliance should not be placed on the forward-looking information because Nine Mile can give no assurance that they will prove to be correct. The Canadian Securities Exchange (CSE) has not reviewed and does not accept responsibility for the adequacy or the accuracy of the contents of this release.
NINE MILE METALS ANNOUNCES COMPLETION OF DDH WD-25-01 AND CONFIRMS TWO ZONES OF VMS MINERALIZATION AT THE WEDGE PROJECT
TORONTO, ONTARIO, CANADA – MONDAY NOVEMBER 26th, 2025, NINE MILE METALS LTD. (CSE: NINE, OTCQB: VMSXF, FSE: KQ9) (the “Company” or “Nine Mile”), is pleased to announce that the 1st drill hole in its Wedge Western Extension Drill Program (DDH-WD-25-01) has been completed to target depth and is in progress on its 2nd hole (DDH-WD-25-02). WD-25-01 was collared along the southern flank of the Wedge Mine and drilled at an azimuth of 335 degrees with a dip of -50 degrees to target the 2 modeled plates in the western extension (Figure 2). DDH WD-25-01 was successful, intersecting approximately 22.40 meters (true width) of massive copper bearing sulphides (VMS – Cu-Pb-Zn-Ag-Au), in the 1st Target Plate. DDH WD-25-01 also intersected a 2nd sulphide zone in Target Plate 2, which is currently being geologically logged, measured, photographed and cut for sampling. A total of 65 sample sections have been identified for base and precious metals analysis (including Antimony) by Actlabs, Fredericton, New Brunswick. The VMS sulphides were visible so our time consuming XRF analysis process was not performed on this large a section to expediate the samples to the labs for certified analysis, also keeping the crew from becoming backlogged in the drill program. All drill core has been measured, logged, photographed, marked and cut for sampling at the company’s warehouse in Bathurst New Brunswick. WD-25-02 was collared on the same drill pad and drilled at an azimuth of 310 degrees and a dip of -50 degrees to intersect the first plate approximately 40 meters further west to extend the mineralized zone along strike. More details will follow when geological logging of the drill core has been completed. FIGURE 4: Massive Copper Bearing VMS Mineralization Gary Lohman, VP Exploration, Director stated, ”We are very pleased with the VMS sulphide mineralization intersects from our first drill hole, WD-25-01. The mineralization was intersected where projected and throughout its width, it is massive and looks nondescript as seen in the images above, however, upon close examination, chalcopyrite (Cu) is seen as very fine disseminations within a matrix of pyrite. With the success of the first hole, the technical team, with the assistance of Apex Geoscience, decided to turn the drill west (WD-25-02) to intersect the VMS sulphide zone along strike and extend the mineralized footprint west. We look forward to building on this success and reporting the ongoing progress of this important Drill program at The Wedge Project”. Patrick J. Cruickshank, MBA, CEO & Director, stated, “the team is working diligently and efficiently to process the core as quickly as possible including carrying out core orientation and markup, geological logging, photography, cutting and sampling, prior to submitting for assay. Our Team is doing a stellar job. We are happy to deliver this update and will provide an update on hole WD-25-02 as soon as possible. Apex Geoscience has been instrumental in their advisory and drill program design along with our entire our Technical Team. We are well on our way with this exciting Drill Program at the Western Extension of the Wedge. A more detailed update shortly once we interpret these 2 holes and make any adjustments or new targets to the program.” About Nine Mile Metals Ltd.: Nine Mile Metals Ltd. is a Canadian public mineral exploration company focused on VMS (Cu, Pb, Zn, Ag and Au) exploration in the world-famous Bathurst Mining Camp, New Brunswick, Canada. The Company’s primary business objective is to explore its four VMS Projects: Nine Mile Brook VMS Project; California Lake VMS Project; and the Canoe Landing Lake (East – West) Project and the Wedge VMS Project. The Company is focused on exploration of Minerals for Technology (MFT), positioning for the boom in EV and green technologies requiring Copper, Silver, Lead and Zinc with a hedge with Gold. Social Media @NineMileMetals Nine Mile Metals @ Nine Mile Metals ON BEHALF OF NINE MILE METALS LTD. “Patrick J. Cruickshank, MBA” CEO and Director T: +1.506-800-0581 E: info@ninemilemetals.com Forward-Looking Information: This press release may include forward-looking information within the meaning of Canadian securities legislation, concerning the business of Nine Mile. Forward-looking information is based on certain key expectations and assumptions made by the management of Nine Mile. In some cases, you can identify forward-looking statements by the use of words such as “will,” “may,” “would,” “expect,” “intend,” “plan,” “seek,” “anticipate,” “believe,” “estimate,” “predict,” “potential,” “continue,” “likely,” “could” and variations of these terms and similar expressions, or the negative of these terms or similar expressions. Forward-looking statements in this press release include that (a) our Geophysics Program will turn its focus next to the Nine Mile Brook Project and our Eastern Portfolio, (b) both Plates A and C are large, massive, strong conductors, having both the length and depth parameters for a potentially large, mineralized body consistent with example deposits throughout the BMC, and (c) we look forward to announcing our Phase 2 Advanced Geophysics results, including full interpretations and high priority targets for our Western Portfolio. Although Nine Mile believes that the expectations and assumptions on which such forward-looking information is based are reasonable, undue reliance should not be placed on the forward-looking information because Nine Mile can give no assurance that they will prove to be correct. The Canadian Securities Exchange (CSE) has not reviewed and does not accept responsibility for the adequacy or the accuracy of the contents of this release.
Nine Mile Metals: ‘Reawakening’ Brunswick legacy in Bathurst
WRITTEN BY Adam Orlando This article is a sponsored feature from Mining.com.au partner Nine Mile Metals. It is not financial advice. Talk to a registered financial expert before makinginvestment decisions. The Bathurst Mining Camp (BMC) is one of the world’s oldest base metals mining districts and one of Canada’s largest volcanic massive sulphide (VMS)deposits. Located in the Miramichi Highlands of New Brunswick, Canada, thecamp covers 3,800km2 and hosts 95 copper, lead, zinc, silver, and goldoccurrences and 45 deposits. The host geology is referred to as the Bathurst Super group. It remains one of the most prospective districts globally for VMS (see image below ), which are 2 accumulations of metal sulphides that precipitate from heated hydrothermal fluid associated with volcanically active under-sea environments. Mining of the Bathurst Mining Camp dates back as early as 1911 when the Nepisiguit Iron Ore Deposit was the only known resource. Today, this legendary and historically significant mining district is seeing a high-tech revival and at the forefront of this modern technological approach is Canadian exploration company Nine Mile Metals (CSE:NINE). With four projects in the district in New Brunswick, covering 136.34km, Nine Mile Metals’ primary business objective is to explore its four VMS projects – Nine Mile Brook VMS Project, California Lake VMS Project, the Canoe Landing Lake (East –West) VMS Project, and the Wedge VMS Project. Legendary mining district reimagined As CEO Patrick J Cruickshank explains to Mining.com.au, the company is positioning itself for the boom in electric vehicles and green technologies requiring copper, lead, zinc, silver while providing a hedge with gold. Exploration is backed by strong historical precedent and leading edge new geophysical technologies, utilising proprietary algorithms and data analytics todefine new mineralisation targets, vital for global clean tech growth.Cruickshank says Nine Mile Metals’ work is guided by the lessons of Brunswick’s success and the belief that the next world-class discovery is still waiting in Bathurst. “We’re combining history with innovation to find it,” the CEO tells this news service. The company is combining historical insight with modern exploration to unlock the next chapter in critical mineral discovery – all within the same neighbourhood as the world-renowned Brunswick #12 and #6 mines. “The assets are world-class. There are deposits in our shadows to be discovered. And you know in this business, critical minerals are only going to get more important, whether you believe it’s EV or clean energy or just copper,base metals, right? Huge disconnect. And there hasn’t been a big discovery in many decades, and supply continues to be an issue with demand increasing on a global scale.” Cruickshank explains. “We’re very confident going forward – we have a roadmap. We have just spentthe majority of 2024 completing cutting-edge geophysics on our entireWestern Portfolio, including California Lake, Canoe Landing and our priorityWedge VMS Project. “Now it’s just a matter of executing our drill programs over our newly defined mineralised target trends and expanding on our Wedge Mine deposit to prove it’s far larger than originally thought. Last year in 2024 we were highly successful in proving the Wedge Mine has an entire new eastern extension previously not known. If we get the mine resource up to 10 million tons, you’ve got a mine.” Nine Miles’ CEO details how being in a mining friendly jurisdiction within the legendary mining district now being re imagined is extremely important, and presents a plethora of benefits and opportunities. “We operate in a 100% mining community with 80 years of exploration or production history, in the best mining jurisdiction in Canada, for example, we’ve never had a permit take longer than 30 days. That’s incredibly powerful for executing our programs in a timely and cost effective manner,” Cruickshank continues. “We are on 100% Crown land, no Indigenous or First Nations issues whatsoever.And there is access to a deep water port year-round, Canadian rail, and a localmining-educated work base, with an incredibly supportive government withlocal support and resources to assist junior mining companies and supportthem to succeed. “We have great project access, with serviced logging roads, ATV and snowmobile trails. Many of our Projects have year round access, except for once you get deeper into the Mining Camp on the western lands. “As long as we have water access we can drill in the winter, it’s easier at times when the ground is frozen, we normally have full access from May – December on most of our lands, with some having year round depending on location and weather. Combined with the most cost effective drilling costs in Canada, we receive a tremendous capital cost return for our work programs, which equates to more metres per dollar than other exploration companies.” Legacy discoveries, modern day pioneers The BMC centrepiece is the Brunswick #12 mine – an underground lead-zinc-copper mine discovered in 1953 and entered production just over a decade later. The Brunswick #12 ore body is the largest deposit in the Bathurst area and was one of the largest underground zinc mines in the world into the late 1990sbefore the mine officially closed in 2013. More than 335 million tonnes of high-grade ore has been mined at Brunswick#12 during that time, giving the mine legendary status for its exceptional size,grade, and longevity. Notably, Nine Miles is positioned just 10km from Brunswick #12 and is actively exploring along the Wedge horizon and other targets with AI and proprietary advanced geophysics. The BMC’s legacy may be 75 years in the making, however Cruickshank notes there remains significant potential for explorers like Nine Mile Metals to capitalise on what remains buried there, particularly for technologically minded explorers. Nine Mile Metals is a new generation explorer working within this historically rich, under explored district using next-generation tools. UAV drones and re-processing utilising proprietary algorithms is part of its strategy. Every 20 years or so, new geophysical technologies create a new wave of discoveries. Could the sector now be riding the crest of that wave? “That’s where we are now. We believe in our technology and our partners. Now we just